SRL Archive - S.M.A.R.T. General and Q/A.

Sup everybody.

I've been running Pyro's guild miner (pure ownage I might add :D) and I just started using it with SMART. Once I started using it with SMART, it keeps giving me an access violation after running for 5-15 minutes (around there) and the script stops because of it. This is really screwing up my autoing and I was wondering if anybody could help me figure out how to fix this error?

[Runtime Error] : Exception: Access violation at address 040010AB in module 'Embedded SMART.dll'. Read of address 07808084 in line 38 in script C:\Program Files\SCAR 3.13\includes\srl/srl/misc/smart.scar

Thanks a lot. Any help is greatly appreciated.

Is your SMART.scar all in order?

Also, try reloading (closing and reopening it) SCAR and use SCAR 3.12c.

If you do that, it should work fine.

Try scar 3.12c
Try updating your Java
If you are running multiple, be sure you got both scars in seperate folders!

Shouldn't using SCAR 3.13 be better?

show the script you are using (so we can check to make sure you setup the script for smart the right way)

Edit: Actually i am completely almost sure the problem is with how you set up the script

Yea I get the same problems, JAD.

What I did, to atleast make the script run somewhat longer, was to put in a Try-Except-Clause. That made it work 5 times as long, but still fucked up eventually. Now I made it Try-Except-Finally, so there's a ridiculously low rate of it fucking up. Still possible, though.

-Knives

From: JAD
Sup everybody.

I've been running Pyro's guild miner (pure ownage I might add :D) and I just started using it with SMART. Once I started using it with SMART, it keeps giving me an access violation after running for 5-15 minutes (around there) and the script stops because of it. This is really screwing up my autoing and I was wondering if anybody could help me figure out how to fix this error?

[Runtime Error] : Exception: Access violation at address 040010AB in module 'Embedded SMART.dll'. Read of address 07808084 in line 38 in script C:\Program Files\SCAR 3.13\includes\srl/srl/misc/smart.scar

Thanks a lot. Any help is greatly appreciated.

lolz?

you're back m8?

did you block me on msn -,-

Hmm… Still not working.

It may be a script problem, but I'm not close to 100% sure.

I'm going to try some other scripts and see if I get the same problem.

No JAD you're right. Still doesn't solve it for me either.
I even incorporated a new Try-Except-Finally-Clause in the "Finally" part of the first TEF-Clause… :S

There's no shit with Wizzup?'s VEM, though. Ran for like 2 hours with no problem at all.

-Knives

Hmm, I don't remember if it was a runtime error or another error, but when I am running SMART and I minimize scar to tray (crtl+m) I get a runtime error almost instantly.

Although I doubt this is a problem it is always good to look at all points that may make the error occur.

Wait:
Did you call SmartSetup? If so, be sure you call it first, and DON'T forget the SetTargetDC(SmartGetDC); or else it'll fuck it, as the canvas has not been initialized yet.

I have it in my SMART File, The SmartSetupEx by Dark_Sniper I think it was.

I have that in my 3 SCAR folders, and the 2 other SCAR's ran flawlessly (In terms of SMART)

It can't be that :S

-Knives

omg post the script, i fixed someone else's prob that was almost just like this

From: mr.klean
Hmm, I don't remember if it was a runtime error or another error, but when I am running SMART and I minimize scar to tray (crtl+m) I get a runtime error almost instantly.

Although I doubt this is a problem it is always good to look at all points that may make the error occur.

There are loads of bugs in minimizing SCAR to the tray since Divi 3.10 I belive.

Im fairly sure its a getcolor looking off the canvas. AS in too big co ords or negative co ords. Which is possible. FFS. The person askign for the script just look in junior members. So just make the call in smart.scar if the co ords too big or too small just correct them

rotfl, im not asking for the script, im asking for the script he set up. I was to see if he has set the script up right because his error looks similar to one i fixed before